A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The content below relating to How to Install a Bathtub is particularly attention-grabbing. Try it and make your own personal conclusions.
Installing a bath tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a new one is additionally a moderately difficult project. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also embeded in the new one. Ensure you have certified yourself for the job as well as fit trying it. As opposed to employing a contractor to take over a halfway-completed project, it is better to consider utilizing one prior to you begin. Possibilities are you may need a professional plumber to make tube links.
This post will certainly help you mount a new bathtub in your restroom if you have actually already bought a new bathtub and don't need to change the setup of your previous water pipes.
Your devices as well as product checklist need to comprise the following:
Getting ready for the Setup
Firstly, the supporting structure supplied with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its final placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing taps can be rather bothersome because of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. As soon as the supply pipes have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the called for setting. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the bathtub till the spirit level reads degree.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system and inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and additionally check the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub should wait till the bath tub has been utilized at least when as this will certainly resolve it right into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The previous type needs to be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, leading to complications with wetness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to allow for the movement experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I'm very fascinated with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed our entry. Those who enjoyed our post if you please make sure you remember to pass it around. Thank you so much for going through it.
Let's solve it, call now! Report this page